Fein Turbo III Vacuum Accessories

HEPA Filter with Hardware

The High Efficiency Particulate Air (HEPA) filter increases filtration to 99.976% of all particles 0.3 microns in size and larger. Includes a flange and screw for mounting.

Click T11HEPA Filter for more info.

1 Micron Filter with Hardware

Increases filtration to 99.97% of all particles 1 micron and over. Includes a flange and screw for mounting.

Click T111MCRN Filter for more info.

Filter Flange

Used with the filter screw to attach either a 1 micron or HEPA filter on to the Turbo III vacuum. Included with the filters listed above.

Click T113002 Filter Flange for more info.

Filter Screw

Used with the filter flange to attach either a 1 micron or HEPA filter on to the vacuum. Included with the filters listed above.

Click T113001 Filter Screw for more info.

Turbo III Vac Dust Bag - 3 Pack

Keeps debris from spreading inside the tank. Cannot be used with the 5 Micron filter. You must use a bag when using either a 1 Micron filter or the HEPA filter.

Click Turbo III Dust Bags for more info.

5 Micron Cloth Filter - 9-77-25 Turbo III

For use with the discontinued 9-77-25 Turbo III Vacuum and has a 13" outer diameter rim. Sits in the bottom of the vac container and will contain 99.97% of all particles 5 micron and over.

Click 913064AGA6 Cloth Filter for more info.

5 Micron Cloth Filter - 9-20-26 Turbo III

For use with the new 9-20-26 Turbo III Vacuum and has a 14-7/8" outer diameter rim. Sits in the bottom of the container and will contain 99.97% of all particles 5 micron and over.

Click 913079AGA6 Cloth Filter for more info.

Anti-Foam Wet Filter

Used in place of all other filters when operating the vac in a wet application.

Click 902042000 Wet Filter for more info.

16' x 1-1/4" Hose

A more convenient hose when using a hand-held power tool or as a second hose for running two power tools. You will need a Flex Hose End Adaptor (#921069A13) or a Vac Step Adaptor (#921072K13) to connect to a hand-held power tool. HINT: Connect two 16' hose using a Vac Step Adaptor to make one 32' hose!

Hose Clip

This clip attaches the power tool cord to a 1-1/4" diameter hose (#921049GN1 - standard equipment with the Turbo II) to prevent entanglement.

Click 921063K13 Hose Clip for more info.

10' x 2-1/4" Hose

This is a replacement hose for the 10' x 2-1/4" hose supplied with the Turbo III Vac. Can be used as a second hose for running two tools.

Click 921120AG13 Hose for more info.

Y-Connector

Operate Two Tools Off One Turbo III Vacuum!
This adaptor connects directly into the vacuum port of the Turbo III. Can be used with just one tool by closing one of its ports.

Click 921086AA13 Y Connector with Cap for more info.

Flex Hose End Adaptor

Used to connect a 1-1/4" diameter vacuum hose to power tools with a 1-1/4" port. One is included with the Turbo III Vac as standard equipment.

Click 921069A13 Adaptor for more info.

Vac Step Adaptor

Used to connect a power tool with a port diameter other than 1-1/4" to a 1-1/4" diameter hose. Determine the fit you need and then cut the adaptor. A very handy device to have around the shop. Almost as handy as duct tape.

Click 921072K13 Step Adaptor for more info.

2-1/4" to 1-1/4" Adaptor

Connects a 2-1/4" diameter hose to most portable tools with a 1-1/4" diameter port.

Click 921005AK13 Vacuum Adaptor for more info.

1-1/2" O.D. to 2-1/4" O.D. Benchtop Adaptor

Connects a 1-1/4" diameter hose to most benchtop machines with a 2-1/4" port.

Powerbrush Kit

The Fein Powerbrush can be used to turn any auto start vac into an upright style house vacuum. Just plug the Powerbrush cord into the front of the vac and put the switch in "auto" position and lower the handle. The power head is self propelled and has a 13" cleaning width with a dual agitator rotating at 1600 beats per minute. The Powerbrush turns on when the handle is released from its upright position. The Powerbrush includes a suction reducing handle, two extension tubes, cable clamps, and 22' cord.

Click PB350 PowerBrush Kit for more info.

Turbo III Vac Accessory Kit

This kit turns your Turbo III vacuum into a shop style vac. Includes 2 extension tubes, handle with built-in suction force reducer, crevice nozzle, upholstery nozzle, furniture brush, floor nozzle (nozzle body and fluid & floor frame) and an anti-foam filter (for wet vacuuming).

Click DW3 Wet-Dry Clean-Up Kit for more info.

MultiMaster Dust Extractor Adaptor Kit

USED ONLY WITH THE MULTIMASTER RS & XL KITS
This adaptor allows the MultiMaster to connect to any Fein vacuum. A step adaptor (#921072K13) might be needed to connect to other brands of vacs.

Click 92602063023 Dust Extraction Kit for more info.

MultiMaster FMM250 Dust Extraction Kit

Allows the MultiMaster to connect to a vacuum for totally dust-free sanding.

Click 92602081010 Dust Extraction Kit for more info.

See all the Sanding Accessories we stock.