Fein Turbo III Vacuum Accessories

HEPA Filter with Hardware

The High Efficiency Particulate Air (HEPA) filter increases filtration to 99.976% of all particles 0.3 microns in size and larger. Includes a flange and screw for mounting.

1 Micron Filter with Hardware

Increases filtration to 99.97% of all particles 1 micron and over. Includes a flange and screw for mounting.

Filter Flange

Used with the filter screw to attach either a 1 micron or HEPA filter on to the Turbo III vacuum. Included with the filters listed above.

Filter Screw

Used with the filter flange to attach either a 1 micron or HEPA filter on to the vacuum. Included with the filters listed above.

Turbo III Vac Dust Bag - 3 Pack

Keeps debris from spreading inside the tank. Cannot be used with the 5 Micron filter. You must use a bag when using either a 1 Micron filter or the HEPA filter.

5 Micron Cloth Filter - 9-77-25 Turbo III

For use with the discontinued 9-77-25 Turbo III Vacuum only. Sits in the bottom of the vac container and will contain 99.97% of all particles 5 micron and over.

5 Micron Cloth Filter - 9-20-26 Turbo III

For use with the new 9-20-26 Turbo III Vacuum. Sits in the bottom of the container and will contain 99.97% of all particles 5 micron and over.

Anti-Foam Wet Filter

Used in place of all other filters when operating the vac in a wet application.

16' x 1-1/4" Hose

A more convenient hose when using a hand-held power tool or as a second hose for running two power tools. You will need a Flex Hose End Adaptor (#921069A13) or a Vac Step Adaptor (#921072K13) to connect to a hand-held power tool. HINT: Connect two 16' hose using a Vac Step Adaptor to make one 32' hose!

Hose Clip

This clip attaches the power tool cord to a 1-1/4" diameter hose (#921049GN1 - standard equipment with the Turbo II) to prevent entanglement.

10' x 2-1/4" Hose

This is a replacement hose for the 10' x 2-1/4" hose supplied with the Turbo III Vac. Can be used as a second hose for running two tools.

Y-Connector

Operate Two Tools Off One Turbo III Vacuum!
This adaptor connects directly into the vacuum port of the Turbo III. Can be used with just one tool by closing one of its ports.

Flex Hose End Adaptor

Used to connect a 1-1/4" diameter vacuum hose to power tools with a 1-1/4" port. One is included with the Turbo III Vac as standard equipment.

Vac Step Adaptor

Used to connect a power tool with a port diameter other than 1-1/4" to a 1-1/4" diameter hose. Determine the fit you need and then cut the adaptor. A very handy device to have around the shop. Almost as handy as duct tape.

2-1/4" to 1-1/4" Adaptor

Connects a 2-1/4" diameter hose to most portable tools with a 1-1/4" diameter port.

1-1/2" O.D. to 2-1/4" O.D. Benchtop Adaptor

Connects a 1-1/4" diameter hose to most benchtop machines with a 2-1/4" port.

Powerbrush Kit

The Fein Powerbrush can be used to turn any auto start vac into an upright style house vacuum. Just plug the Powerbrush cord into the front of the vac and put the switch in "auto" position and lower the handle. The power head is self propelled and has a 13" cleaning width with a dual agitator rotating at 1600 beats per minute. The Powerbrush turns on when the handle is released from its upright position. The Powerbrush includes a suction reducing handle, two extension tubes, cable clamps, and 22' cord.

Turbo III Vac Accessory Kit

This kit turns your Turbo III vacuum into a shop style vac. Includes 2 extension tubes, handle with built-in suction force reducer, crevice nozzle, upholstery nozzle, furniture brush, floor nozzle (nozzle body and fluid & floor frame) and an anti-foam filter (for wet vacuuming).

MultiMaster Dust Extractor Adaptor Kit

USED ONLY WITH THE MULTIMASTER RS & XL KITS
This adaptor allows the MultiMaster to connect to any Fein vacuum. A step adaptor (#921072K13) might be needed to connect to other brands of vacs.

MultiMaster FMM250 Dust Extraction Kit

Allows the MultiMaster to connect to a vacuum for totally dust-free sanding.

Includes:

• 2 Perforated Sanding Pads
• 5 Each 60, 80, and 120 Grit Perforated Sanding Sheets
• Extraction Hood and Suction Tube
• 2 Hose Nozzles
• 2 Adaptors for 1" and 1-1/4" Vacuum Hose

See all the Sanding Accessories we stock.